Silvia Club of NSW https://forum.silviansw.com/ |
|
Killabeez S13 driftpig - fml car no more :( https://forum.silviansw.com/viewtopic.php?f=24&t=32963 |
Page 1 of 3 |
Author: | Killabeez [ Wed Mar 18, 2009 11:29 pm ] |
Post subject: | Killabeez S13 driftpig - fml car no more :( |
Heya, I finally have a replacement track only car to replace my old 31 drifter. Its uncomplied but came in under the 15+yo rule so can be complied later on if I can be arsed. I picked it up in Melbourne and drove it back to Sydney, fuc%ing annoying drive when you have a stripped interior and a straight through exhaust with an external gate. Anyway you'll probably see it around some drift days (and hopefully time attack too). Here it is in its original form, I have some plans for it in the very near future including a backyard paint job but I just need to fix the left driveshaft 1st which is about as loose as a two dollar... Existing mods are: Blacktop SR (180sx) FMIC Apexi Rx6 high mount turbo kit, P16 Apexi Manifold Apexi External Gate Power FC with hand controller Nismo 740cc injectors Exedy Heavy Duty Button Clutch Apexi Pod Z32 AFM Bosh 040 Pump Alloy Overflow tank Alloy Catchcan Exhaust is straight through with twin 3" stainles pipes out the back Tuned on 100octane fuel for 216kw at 16psi Large B&M oil cooler and relocater kit Vertex side skirts Gold/Bronze 17 x 9 Drifteks BN rear bar Vented Bonnet Bride Ergo seat OMP racing harness Nardi classic steering wheel HKS Turbo timer Flared rear guards JIC coilovers all around ISC rear camber and Toe arms Front and rear strut braces Half cage (tein sticker on it??) Castor rods Spacers on tie rods Brand new front rotors SR20DET New front and rear TRW Lucas pads 1.5way differential Engine dampener Handbrake button RAS Alloy pineapples My plans are (in order or importance): Fix driveshaft - DONE Fix fuel sender gauge Fix Speedo - DONE Change plugs/oil/fuel filter - DONE Fix leaky turbo gasket - DONE Re-tune to 98 octane Fix up headlight and taillight wiring issues 50mm radiator with clutch fan and shroud - DONE Saber series 2 guages - DONE Bee-r Rev limiter - DONE Trust sump - DONE Bash plate - DONE Maybe S14/Z32 tie rods if they fit Bodykit - DONE Change steering wheel to dished suede type - DONE Install rear speakers and head unit Paint - DONE Probably some other minor shit I havent thought of yet Here are some pics And finally a pic of the car in action (fron the previous owner) [/img] |
Author: | (Locky) [ Wed Mar 18, 2009 11:35 pm ] |
Post subject: | |
this thing looks like a weapon, not bothering with the 180 anymore are you trying to make it more street with the speakers and that ???? oh and s14 tierods fit, aslong as you have s14 tie rod ends as well (i mat have a set for sale soon ) |
Author: | Killabeez [ Wed Mar 18, 2009 11:44 pm ] |
Post subject: | |
Yeah it sounds nucking futs, gotta get a BOV as well though as it flutters like a VL, not the best pics, I'll take some more during the week it looks fat as. Ive got a spare head unit and speakers which I'll throw in there so I can listen to tunes whilst drifting. 180 is ready to go I just need to fix the oil leak from the china oil cooler so I can be allowed on track. Its set up quite well as well and I'll be using it as a backup drift car when this one breaks. I'm also considering pulling the 1.5 way out of this thing and swapping it with the locker I have in the 180. I'm interested in those S14 tie rods and ends if you end up selling em, as I've seen what happened to your S13 tie rods (can you say banana) I also have some URAS tie rods and Kazama tie rod ends which I'll probably put in the Silvia and use the S14 ones in the 180. |
Author: | too_much_boost [ Thu Mar 19, 2009 7:14 am ] |
Post subject: | |
Neat! |
Author: | whyte [ Thu Mar 19, 2009 10:47 am ] |
Post subject: | |
looks tough, is the exhaust wonky? how much did you buy it for if you dont mind me asking |
Author: | too_much_boost [ Thu Mar 19, 2009 10:51 am ] |
Post subject: | |
Also you should really change the mounting points of that harness. You will do yourself a serious mischief if you have an acco with them like that |
Author: | Mr Bean [ Thu Mar 19, 2009 11:35 am ] |
Post subject: | |
sweet as it has the bonnet i want! any idea where/who made it? |
Author: | Killabeez [ Thu Mar 19, 2009 12:10 pm ] |
Post subject: | |
Lets just say I got it for a shitload less than what it is worth as its uncomplied, crappy paintwork, and had a minor hit in the right rear tailight area abaou the size of a fist. The exhaust is a twin pipe setup which is offset, the right is about an inch lower than the left, they also stick out about 5 inchs past the rear bar. Yeah I plan on making a bar for the harness or mount the eyelets higher as I hit a wall at EC a few years back in a 31 with a similar setup, it compressed my spine a bit which made it sore for weeks. Bonnnet is acually a stocky which has had the centre cut out of it with a fibreglass vent (maybe topstage or mfx) put in. Its a pretty dodge job with heaps of bog but it does the job. I think I should be able to fix it up. |
Author: | JayS14 [ Thu Mar 19, 2009 6:27 pm ] |
Post subject: | |
Nice work, looks fat. Do you have spacers on the 9" teks or are S13 gards just that weak? |
Author: | (Locky) [ Thu Mar 19, 2009 6:56 pm ] |
Post subject: | |
it would have to be spacer or a 9.5 |
Author: | Killabeez [ Thu Mar 19, 2009 7:21 pm ] |
Post subject: | |
yep 17 x 9 all the way around, with 25mm spacers, yes s13 are weaksauce |
Author: | Siddr20 [ Sat Mar 21, 2009 9:50 pm ] |
Post subject: | |
WOW very nice buildup!! Looks tough too |
Author: | i want a silvia [ Sat Mar 21, 2009 9:59 pm ] |
Post subject: | |
Uncomplied and you drove it back from Melbourne...?! You are brave! |
Author: | haikii [ Sat Mar 21, 2009 10:20 pm ] |
Post subject: | |
I know hey, you have a set of balls on ya mate. Can't wait till i see this on track! get rid of that horrid stencil work on the door though its so ugly hahahaha |
Author: | Killabeez [ Wed Mar 25, 2009 4:00 pm ] |
Post subject: | |
Yeah I need to give it a quick spray, except its sprayed in 2 pack primer so I'll need to go over that with spray putty or sand it down as I want to spray it in acrylic or enamel |
Page 1 of 3 | All times are UTC + 10 hours [ DST ] |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |