Silvia Club of NSW
https://forum.silviansw.com/

Guard/rear lipping/arching... Who does?
https://forum.silviansw.com/viewtopic.php?f=2&t=28818
Page 1 of 2

Author:  4_SI_WAY [ Sat Oct 20, 2007 3:32 am ]
Post subject:  Guard/rear lipping/arching... Who does?

Any help?

Author:  MAXBOOST [ Sat Oct 20, 2007 5:51 am ]
Post subject: 

Luis - aka drift garage. its been asked here and answered here before so do a search if you want his details.

Or do a home-job and bog it up..

Author:  badhairdave [ Sat Oct 20, 2007 8:33 am ]
Post subject: 

www.driftgarage.com.au

Author:  David [ Sat Oct 20, 2007 1:10 pm ]
Post subject: 

+1 for luis

he did mine.

Author:  Serial Killa [ Sat Oct 20, 2007 3:39 pm ]
Post subject: 

Hammertime :P

Author:  4_SI_WAY [ Sat Oct 20, 2007 5:55 pm ]
Post subject: 

Thanks guys, have contacted Luis.

Author:  oRiCLe [ Sun Oct 21, 2007 5:54 pm ]
Post subject: 

Sydney Guard Rolling
0432109331

Mobile service, guarantees no paint chipping for lipping, will come to you and good prices :P he just came and lipped & flared my guards yesterday arvo for me, did a nice job. He does alot of panel and tyre shops guard lipping.

Image
(the ripples were from when i attempted to lip the guards with a hammer, not his doing :D and i did get them rolled out about 20-30mm so it did a fair bit of stretching to the guards, but the car is going to the panel beater next week anyway to get resprayed...so that will all be fixed)

Tell him Hilarious Motorsport reccomended you :D

Author:  EVILS15 [ Mon Oct 22, 2007 11:40 pm ]
Post subject: 

thanks oricle, I booked him in today.

Author:  _Wing_ [ Fri Oct 26, 2007 4:27 pm ]
Post subject: 

drift garage rippled my guards with just a roll of the lips, and rolled it to the ~9o'clock mark - like my rubber is going to rub there :roll:

Author:  too_much_boost [ Fri Oct 26, 2007 5:38 pm ]
Post subject: 

I'm getting my rear guards flared by driftgarage tomorrow. I'm after about 20mm, so there might be some buckling of the panel. I guess i'll find out

Author:  oRiCLe [ Fri Oct 26, 2007 5:50 pm ]
Post subject: 

too_much_boost wrote:
I'm getting my rear guards flared by driftgarage tomorrow. I'm after about 20mm, so there might be some buckling of the panel. I guess i'll find out


haha expect that, mines flared about that and it did buckle, especially on the passenger side :P not so much on the drivers side as there is extra strength on the fuel flap

Author:  GOD_11K [ Sat Oct 27, 2007 2:45 am ]
Post subject: 

what wheel sizes will require 20-30mm flaring?

i'm just curious as i might need to get mine done soon too but was hoping to get away with just simple rolling on the lip. my wheels are only 17x9 +34

Author:  Serial Killa [ Sat Oct 27, 2007 2:50 am ]
Post subject: 

GOD_11K wrote:
what wheel sizes will require 20-30mm flaring?

i'm just curious as i might need to get mine done soon too but was hoping to get away with just simple rolling on the lip. my wheels are only 17x9 +34


I'd take a stab at something like 10.5 inches on the rear and 9.5 on the front??

Author:  GOD_11K [ Sat Oct 27, 2007 2:59 am ]
Post subject: 

Serial Killa wrote:
GOD_11K wrote:
what wheel sizes will require 20-30mm flaring?

i'm just curious as i might need to get mine done soon too but was hoping to get away with just simple rolling on the lip. my wheels are only 17x9 +34


I'd take a stab at something like 10.5 inches on the rear and 9.5 on the front??


yeah i'm thinking it would be something around there. i should be sweet then :)

Author:  too_much_boost [ Sat Oct 27, 2007 5:43 am ]
Post subject: 

GOD_11K wrote:
what wheel sizes will require 20-30mm flaring?

i'm just curious as i might need to get mine done soon too but was hoping to get away with just simple rolling on the lip. my wheels are only 17x9 +34


If you are running 235/45/17, then you will get away with only lipping the rear on those rims

I'm putting on 17x9 (+9) all round. These will sit 25mm further out than yours

I'll upload pics this arvo

Page 1 of 2 All times are UTC + 10 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/