| Silvia Club of NSW https://forum.silviansw.com/ |
|
| intercooler https://forum.silviansw.com/viewtopic.php?f=2&t=21491 |
Page 1 of 1 |
| Author: | 2hundge [ Sun Mar 19, 2006 10:30 pm ] |
| Post subject: | intercooler |
hey guys looking at jus jap an there fmic jus curious if there any good an is it worth buying one an getting someone to do the custom piping thanks |
|
| Author: | cypher1024 [ Sun Mar 19, 2006 10:57 pm ] |
| Post subject: | |
You'd probably be better off just getting the whole kit including piping. Otherwise if you're just looking at getting a core, you could probably get one cheaper off one of the nissansilvia.com sponsors. I can't tell you who though becuase I don't go there any more. |
|
| Author: | ThuanSUX [ Mon Mar 20, 2006 2:16 pm ] |
| Post subject: | |
It'd be much cheaper if you got it as a kit. Custom piping cost much more than cores. |
|
| Author: | 2hundge [ Mon Mar 20, 2006 8:55 pm ] |
| Post subject: | |
ok thanks guys no worries he jus said there out of stock for the piping only cores left.. but thanks |
|
| Author: | JayS14 [ Mon Mar 20, 2006 9:05 pm ] |
| Post subject: | |
The HYBRID kits don't cost much and are very good for what they are. I've got one and no problems, real easy to fit. |
|
| Author: | Boosted_200 [ Tue Mar 21, 2006 12:59 pm ] |
| Post subject: | |
If you cant get piping with it, your probably better off getting a Hybrid kit. Ive got one on my car too and am happy with it. Custom piping can cost up to and over $600 installed. Just look out for the Hybrid copy kits, ive seen pics of the inside of the piping and it looked pretty nasty. |
|
| Author: | cypher1024 [ Wed Mar 22, 2006 12:44 am ] |
| Post subject: | |
If you can, also try to get t-bolt clamps. They're the ones that use a bolt rather than a screw to tighten them, which makes the a lot tougher. |
|
| Author: | ZEi250t [ Wed Mar 22, 2006 1:00 am ] |
| Post subject: | |
luke where did you get yours from? i need around 10 of them for my car when i finally get around to doing some stuff |
|
| Author: | 2hundge [ Wed Mar 22, 2006 10:06 am ] |
| Post subject: | |
thats really good for the imformation guys thanks alot i will look into now as i need one really soon.. |
|
| Author: | whyte [ Wed Mar 22, 2006 11:23 am ] |
| Post subject: | |
Quote: luke where did you get yours from? i need around 10 of them for my car when i finally get around to doing some stuff
shift performance sell 3" t bolt clamps for like $11 each. or ebay sell them in bulk like 10 x 3" t bolt clamps for like $30 or so. |
|
| Author: | ZEi250t [ Wed Mar 22, 2006 11:36 am ] |
| Post subject: | |
hmm i didnt think of ebay, for $11 each ill give that place a miss. i guess enzed or something might have some good ones. plumbing stores too |
|
| Author: | Prince Chiba [ Wed Mar 22, 2006 12:12 pm ] |
| Post subject: | |
yeh i need some t bolt clamps as well, ages ago there was this sponsor offering a special, i think it was 50$ for 10. i should have gotten them. |
|
| Author: | mokompri [ Wed Mar 22, 2006 2:42 pm ] |
| Post subject: | |
i wouldnt bother unless your running crazy amounts of boost, there so pricey normal quality ones should be fine |
|
| Author: | ZEi250t [ Wed Mar 22, 2006 2:44 pm ] |
| Post subject: | |
i would but i dont like the way the worm type ones bend and look like they are about to spring open at any time. id prefer to spend the money and do it properly |
|
| Author: | mokompri [ Wed Mar 22, 2006 3:30 pm ] |
| Post subject: | |
the ones i got with my blitz kit work just fine, they dont bend either never had any pop off and thats running up to 20psi |
|
| Page 1 of 1 | All times are UTC + 10 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|