Silvia Club of NSW
https://forum.silviansw.com/

Intercooler Piping
https://forum.silviansw.com/viewtopic.php?f=1&t=30819
Page 2 of 2

Author:  Timo [ Fri May 23, 2008 2:17 pm ]
Post subject: 

i installed a hybrid kit on mine. i had to shave a bit of the reo bar (on the inside, doesnt look like it would affect the structural integrity), and had to shave a fair bit of the front bar back. i used an angle grinder to do both.

Author:  sil:xtc [ Tue May 27, 2008 1:13 pm ]
Post subject: 

Yea having a closer look on the inside of the front bar and it looks like i will need to cut a bit of the front bar on the inside.

Here is a pic of the piping - haven't actually received it yet.

Image

Picture of my engine bay before mods NOTE: i now have an apexi pod.
http://forum.silviansw.com/download.php?id=1094


Bring the help on hahaha what goes where ? Also i have stock plumb back bov and i don't wish to change it to an external will this effect the setup.

If it helps i might post pic's of my engine bay cause their are a few lines connected to my stock smic piping that i have no idea what they do and where they will eventually go :P

- Joey -

EDIT - Link to a pic of engine bay when i first bought the car.

Author:  LISTEN 180SX [ Tue May 27, 2008 3:39 pm ]
Post subject: 

Timo wrote:
i installed a hybrid kit on mine. i had to shave a bit of the reo bar (on the inside, doesnt look like it would affect the structural integrity), and had to shave a fair bit of the front bar back. i used an angle grinder to do both.


I had to make the same modifications for my trust v-spl kit too. although I used a jigsaw for the reo bar, and a hacksaw blade to cut/shave the front bar

Author:  sil:xtc [ Thu May 29, 2008 9:12 pm ]
Post subject: 

Have recieved the piping and assembled in the correct order, or at least i think i did..... lol
Let me know if i have done anything wrong. :D

http://img100.imageshack.us/my.php?image=picture140ze6.jpg
- Joey -

Author:  Timo [ Fri May 30, 2008 2:11 pm ]
Post subject: 

sil:xtc wrote:
Have recieved the piping and assembled in the correct order, or at least i think i did..... lol
Let me know if i have done anything wrong. :D

http://img100.imageshack.us/my.php?image=picture140ze6.jpg
- Joey -


looks good mate. it will look even better on the front of your car :)

Author:  sil:xtc [ Sun Jun 01, 2008 6:53 pm ]
Post subject: 

Ok so i have found off JDM:15T that i cannot use my factory BOV, can any on else confirm this is their a way around this ??

If not what are some other alternatives as far as BOV, i would prefer a plumb back but thinking ahead i wouldnt mind getting a dual port for when i intend to run more boost - having the advantage of plumb back & atmospheric. !!

Edit: Looks like I'll be leaning towards Turbo smart Blow-off Valve Type-3 Dual Port they have a few to choose from:
25mm outlet
29mm "
32mm "
34mm "
38mm "

Is their a particular size I'm looking at or it doesn't matter ? Thanks :D

- Joey -

Author:  vells [ Fri Jul 25, 2008 11:51 pm ]
Post subject: 

I got my piping from unique auto sports in seven hills

Page 2 of 2 All times are UTC + 10 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/